Siemens SIMOTION P320-3 Manual Download

Page: 95 / 150

Connecting

6.3 Connecting peripheral equipment

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

6.3

Connecting peripheral equipment

NOTICE

Connect only peripheral devices approved for industrial applications conforming to

EN 61000-6-2 / IEC 61000-6-2.

CAUTION

Strictly adhere to the specifications for the peripheral devices.

NOTICE

The connected or built-in peripherals, such as USB drives, should not introduce a counter-

EMF into the device.
Generation of reverse voltage greater than 0.5 V to ground on + 3.3 VDC / + 5 VDC / + 12

VDC at a connected or installed component can prevent normal operation or destroy

components of the device.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands