Siemens SIMOTION P320-3 Page 91 Manual Download

Page: 91 / 150

Installing/Mounting

5.5 Mounting the SIMOTION panel front

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

Procedure

To screw on the panel front, proceed as follows:
1.

Follow the installation instructions.

Drill four mounting holes at the prepared mounting cutout in accordance with the

specified installation dimensions.

Carefully drill the front drill-hole covers on the control unit from behind.

CAUTION

Ensure that no metal cuttings enter the device. Cover the device with plastic sheeting, or

use a suction device when drilling.

'ULOOKROHFRYHUV

Figure 5-8

Designated location for holes on the control unit

Place the assembled control unit and computer unit components into the recessed

mounting cutout from the front so that the holes are aligned.

Secure the control unit by inserting suitable screws through the holes and attaching nuts

(torque 0.4 ... 0.5 Nm).

Note
The mounting depth increases by 21 mm when an optical drive is installed in the device.

Take the dimensions from the dimension drawings.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands