Siemens SIMOTION P320-3 Manual Download

Page: 78 / 150

Installing/Mounting

5.1 Installing SIMOTION P320-3

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

Mounting brackets on the device

Two mounting brackets are included in the device package. They can be attached to the

device with four screws supplied.

Steps for installing the mounting brackets
Install the mounting brackets on the

device.

Note
Required tools
You need a TORX T20 screwdriver to remove the mounting clamps and mount the mounting

brackets.

Mounting/installing the device

For dimensions of the device variants with mounting clamps see Dimension drawings of the

device with mounting brackets (Page 119).

Examples of mounting types
Material

Hole diameter

Fixing

Concrete

8 mm diameter

60 mm depth

Dowel: 8 mm diameter

50 mm length

Screws: 4 mm diameter

50 mm length

Plasterboard

(min. 13 mm thick)

14 mm diameter

Cavity fixings: 4 mm diameter

50 mm length

Metal

(min. 2 mm thick)

5 mm diameter

Metal screws M 4: 4 mm diameter

15 mm length

WARNING

Ensure that the wall or ceiling can hold four times the total weight of the device (including

the mounting brackets and additional expansion modules).

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands