Siemens SIMOTION P320-3 Manual Download

Page: 33 / 150

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

Hardware description

3.1

SIMOTION P hardware components

Note
The order numbers of the components described below can be obtained from the online

catalog in the Siemens A&D

SIMOTION P complete system

SIMOTION P (SIMOTION P320-3)

SIMOTION P spare parts

As standard, a SIMOTION P320-3 consists of the following hardware components:
● SIMOTION PC unit SIMOTION P320-3
● Back-up battery for the motherboard of the SIMOTION P320-3

Optional components

The following hardware components are optional and can be ordered separately:
Operation and display
● SIMOTION panel fronts

–  12" panel front SIMOTION P012T (touch screen)
–  12" panel front SIMOTION P012K (keys)
–  15" panel front SIMOTION P015T (touch screen)

● Panel PC Remote Kit

Power supply of the SIMOTION P320-3

The power supply must meet the requirements liste d at Power supply (Page 127). This can

be ensured by using the following devices, for example:
● SITOP smart 24 V/10 A
● Optional 24 VDC UPS

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands