Siemens AGM60.4A9 Basic Documentation Download Page 9

Page: 9 / 248

9/248

Building Technologies Division

Basic Documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

Contents

25.09.2013

14.2

Modulating operation ................................................................................... 143

14.3

2-stage operation ......................................................................................... 143

14.4

3-stage operation ......................................................................................... 144

Fuel meter input X75 pin 1 / X75 pin 2 ..................................................... 145

15.1

Configuration of fuel meter .......................................................................... 145

15.1.1

Types of fuel meters .................................................................................... 145

15.1.2

Configuration of pulses per volume unit ...................................................... 145

15.1.3

Reading and resetting the meter readings .................................................. 145

15.2

Fuel throughput ........................................................................................... 146

15.2.1

Configuration ............................................................................................... 146

15.2.2

Reading out the fuel throughput .................................................................. 146

Connection and internal diagram ............................................................ 147

Special feature: Burner identification (ID) ............................................... 148

Connection to superposed systems ........................................................ 148

18.1

General information and building automation functions .............................. 148

18.2

Modbus ........................................................................................................ 150

PC software ACS410 ................................................................................. 151

Error history ............................................................................................... 152

20.1

Error classes ................................................................................................ 152

20.2

Makeup of error history ................................................................................ 153

Lifecycle function ...................................................................................... 154

Safety notes on use of the AZL2... ........................................................... 154

Operating the AZL2... unit ......................................................................... 155

23.1

Description of unit/display and buttons ........................................................ 155

23.2

Meaning of symbols on the display ............................................................. 156

23.3

Brightness of display ................................................................................... 156

23.4

Special functions ......................................................................................... 157

23.4.1

Manual lockout ............................................................................................ 157

23.4.2

Manual control (manual request for output) ................................................. 157

23.5

Timeout for menu operation ........................................................................ 158

23.6

Backup / restore .......................................................................................... 159

23.6.1

Backup ......................................................................................................... 160

23.6.2

Restore ........................................................................................................ 162

Operation of basic unit via the AZL2... .................................................... 164

24.1

Normal display ............................................................................................. 164

24.1.1

Display in standby mode ............................................................................. 164

24.1.2

Display during startup / shutdown ............................................................... 164

24.1.2.1.

Display of program phases .......................................................................... 164

24.1.2.2.

Display of program phase with remaining running time until end of the
phase is reached ......................................................................................... 164

24.1.2.3.

List of phase displays .................................................................................. 165

24.1.3

Display of operating position ....................................................................... 166

24.1.4

Fault status messages, display of errors and info ....................................... 167

24.1.4.1.

Display of errors (faults) with lockout ........................................................... 167

24.1.4.2.

Reset ........................................................................................................... 167

Summary of Contents for AGM60.4A9

























































































































































































































































Search results

Summary of Contents for AGM60.4A9

Reviews:

Siemens AGM60.4A9, Basic Documentation, Page: 9 / 248

Search results

Summary of Contents for AGM60.4A9

Reviews: