Siemens AGM60.4A9 Basic Documentation Download Page 6

Page: 6 / 248

6/248

Building Technologies Division

Basic Documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

Contents

25.09.2013

4.5.1

Terminal output

Inputs

................................................................................... 37

4.5.2

Terminal output

Outputs

................................................................................ 37

4.5.3

Cable lengths ................................................................................................. 38

4.5.4

Cross-sectional areas .................................................................................... 38

4.5.5

Electrical connections of actuators ................................................................ 38

4.5.6

Environmental conditions ............................................................................... 38

Dimensions ................................................................................................... 39

5.1

LMV36... ......................................................................................................... 39

5.2

AGM60... ........................................................................................................ 40

Display and diagnostics .............................................................................. 41

Basic unit ...................................................................................................... 42

7.1

Description of inputs and outputs ................................................................... 42

7.2

Flame detectors ............................................................................................. 43

7.2.1

Loss of flame .................................................................................................. 44

7.2.2

Extraneous light ............................................................................................. 44

7.2.3

No flame at the end of safety time (TSA) ....................................................... 45

7.2.4

Flame intensity ............................................................................................... 45

7.2.5

Supervision of flame detector ........................................................................ 45

7.3

Digital inputs .................................................................................................. 46

7.3.1

Safety loop X3–04 (optional pressure switch-max (Pmax)), pin 1 and 2 ....... 46

7.3.2

(Burner flange) X3–03, pin 1 and 2 ................................................................ 47

7.3.3

Input for external controller (ON / OFF) X5–03, pin 1 .................................... 47

7.3.4

Air pressure switch (APS) X3–02 ................................................................... 48

7.3.5

Gas pressure switch for gas valve proving (P LT) X9-04 ............................... 49

7.3.6

Gas pressure switch-min (Pmin), start release gas X5–01 ............................ 50

7.3.7

Oil pressure switch-min (Pmin) X9-04 (X5–01 on AGM60...) ........................ 51

7.3.8

Setting the time for checking the pressure switch .......................................... 52

7.3.9

Gas / oil pressure switch-max (Pmax) / or POC contact, start release
oil X5–02 ........................................................................................................ 53

7.3.10

Fuel selection ................................................................................................. 56

7.3.11

Reset X8-04, pin 1 ......................................................................................... 56

7.4

Digital outputs ................................................................................................ 57

7.4.1

Output alarm type No-SI X3–05 pin 2 ............................................................ 57

7.4.2

Fan motor contactor type SI X3–05, pin 1 ..................................................... 57

7.4.3

Fan continuous purging X3–05, pin 3 ............................................................ 57

7.4.4

Output ignition (Z) type SI (IGNITION) X4–02 ............................................... 58

7.4.5

Outputs fuel valves type SI (V1...V3 / PV) X8–02, X7-01, X7-02 ................... 59

7.4.6

Output safety valve (SV) type SI X6–03 / magnetic clutch ............................ 61

7.4.7

Output for indication of operation X8-04 pin 2 ............................................... 61

7.5

Program sequence ......................................................................................... 62

7.5.1

Time parameters ............................................................................................ 62

7.5.2

Valve proving ................................................................................................. 64

7.5.3

Valve proving with separate pressure switch (P LT) X9-04 ........................... 65

7.5.4

Valve proving via gas pressure switch-min X5-01 ......................................... 66

7.5.4.1.

Lockout phase (phase 00) ............................................................................. 66

7.5.4.2.

Safety phase (phase 02) ................................................................................ 67

7.5.5

Special functions during the program sequence ............................................ 68

7.5.5.1.

Reset / manual lockout .................................................................................. 68

Summary of Contents for AGM60.4A9

























































































































































































































































Search results

Summary of Contents for AGM60.4A9

Reviews:

Siemens AGM60.4A9, Basic Documentation, Page: 6 / 248

Search results

Summary of Contents for AGM60.4A9

Reviews: