manualshive.com logo in svg

Siemens AGM60.4A9, Basic Documentation, Page: 57 / 248

Share
Download
Siemens AGM60.4A9 Basic Documentation Download Page 57

 

57/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

7 Basic unit 

25.09.2013 

7.4 Digital 

outputs 

 
Safety-related outputs, type SI

 

 
Using a contact feedback network (CFN), these contacts are read back by the 
microcomputers and checked for their correct positions. 

 
Non-safety-related outputs, type No-SI 

 
These outputs are not monitored by the contact feedback network (CFN) and, for this 
reason, can only be used for non-safety-related actuators, or actuators made safe in 
some other form (e.g. alarm). 
 

7.4.1 Output alarm

 

type No-SI X3–05 pin 2 

 

LMV...

Bild 282/0309

X3

-0

5

Alarm

 

Figure 29: Output alarm X3-05 

 
Output for connection of an alarm lamp or horn. 
The output is activated when the unit is in the lockout position (phase 00). 
This output can also be used to indicate start prevention. 
 

7.4.2  Fan motor contactor type SI X3–05, pin 1 

 

 

LMV...

Bild 283e/1109

X3

-0

5

Fan motor contactor

 

Figure 30: Fan motor contactor X3-05 

 
Output for control of a fan power contactor (200 VA). In accordance with the sequence 
diagrams, the fan is on in phase 22 (refer to chapter 

Sequence diagrams

). 

 

7.4.3  Fan continuous purging X3–05, pin 3 

 

LMV...

Bild 284e/1010

X3

-0

5

Continuous fan operation

 

Figure 31: Continuous fan operation X3-05 

 
If continuous purging is required, the fan motor contactor must be connected to 

Continuous fan operation – X3-05

, pin 3. This terminal is tapped behind the unit fuse 

and the safety loop (refer to chapter 

Continuous fan

). 

 

Summary of Contents for AGM60.4A9

























































































































































































































































Reviews:

No comments