Siemens AGM60.4A9 Basic Documentation Download Page 199

Page: 199 / 248

199/248

Building Technologies Division

Basic documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

28 Parameter level

25.09.2013

h min s

ild 117

707

Phase

Traveling to ignition

position

Wait until the burner is operating and symbol

▲

▼

is no longer highlighted!

The startup sequence stops in phase 36

Traveling to ignition position

The ignition point can be adjusted under cold conditions.

and

as well as

and

and

h min s

ild 118

707

Ignition position

can only be set after symbol

▲

▼

is no longer highlighted.

For fuel, keep

depressed, for air

, as

well as for VSD

and

Press

to adjust the value.

When symbol

▲

▼

is no longer highlighted,

the next curvepoint

can be selected with

h min s

ild 117

707

Phase

Traveling to ignition

position

h min s

ild 119

707

Phase

Preignition

h min s

ild 120

707

Phase

1st safety time

(ignition transformer ON)

h min s

ild 121

707

Phase

1st safety time

(ignition transformer OFF),

preignition time OFF

h min s

ild 122

707

Phase

Interval 1

Summary of Contents for AGM60.4A9

























































































































































































































































Search results

Summary of Contents for AGM60.4A9

Reviews:

Siemens AGM60.4A9, Basic Documentation, Page: 199 / 248

Search results

Summary of Contents for AGM60.4A9

Reviews: