manualshive.com logo in svg

Siemens AGM60.4A9, Basic Documentation, Page: 105 / 248

Share
Download
Siemens AGM60.4A9 Basic Documentation Download Page 105

 

105/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

10 Connection to load controllers 

25.09.2013 

10.3 Manual output 

 
A manual output can be set with the 

Normal display

 of the display and operating unit or 

via the PC software. 
 

Manual output via the display and operating unit 

 
Manual output can be activated or adjusted by keeping the 

F 

button depressed for at 

least 1 second and by pressing the 

+

 or 

–

 button. 

Output 

0

 means 

Manually off

. 

As long as manual output is active, the output appearing on the normal display blinks. 
To deactivate and to change to automatic operation, press 

Esc

 for 3 seconds. 

If 

Manually off

 is activated, it is stored via mains OFF. 

On power return, the burner assumes the 

Manually off

 position (

OFF

 blinking) (refer to 

chapter 

Operation

). 

 
Fuel changeover resets the manual output to 

Invalid

. 

 
Exception: 
Setting 

Manually off

 is maintained after fuel changeover also. 

 

Activation of 

Manually off

 in operation 

To activate 

Manually off

, first run the system to the minimum output limit. Then, keep the 

F 

button depressed for at least

 

1 second and press the 

–

 button. 

 

Manually off

 is activated by releasing the 

F

 button and by pressing again the 

– 

button. 

 

 

Caution! 

Manually off

 must not be used by itself to put a burner out of operation when 

doing mounting work, or when the burner is not ready for operation. The safety 
notes in chapter 

Safety notes

 must be observed! 

 

Manual output via the PC software 

 
Refer to description of the PC software (J7352). 
 

10.4 Output with curve settings 

 
To set the curves via the display and operating unit or the PC software, a special 
parameterization output is provided. Using this output, it is also possible to approach the 
point of ignition. The output is delivered automatically and cannot be set manually. It is 
only mentioned here for the sake of completeness. 
 

Summary of Contents for AGM60.4A9

























































































































































































































































Reviews:

No comments