manualshive.com logo in svg

Siemens AGM60.4A9, Basic Documentation, Page: 239 / 248

Share
Download
Siemens AGM60.4A9 Basic Documentation Download Page 239

 

239/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

30 Error code list 

25.09.2013 

Error 
code 

Diagnostic code 

Meaning for the LMV36... system 

Remedy 

87 # 

Error 

air 

actuator 

 

 0 

Position 

error 

Target position could not be reached within the required tolerance band. 

 Check to see if actuator is locked or overloaded. 

 

Bit 0 

Valency 1 

Line interruption 

Line interruption detected at actuator’s terminals. 

 Check wiring (voltage X53 across pin 5 or 6 and pin 2 >0.5 V). 

 

Bit 3 

Valency 

 8 

Curve too steep in terms of ramp rate

 

Check position differential between the curvepoints and the modulating operating ramp setting 
(parameter 544). 
1. Modulating operating ramp 32 seconds 
The slope of the curve may be a maximum position change of 31° (15° for SQM33.6 and 9° for 
SQM33.7) between 2 curve points in modulating mode. 
2. Modulating operating ramp 64 seconds 
The slope of the curve may be a maximum position change of 62° (30° for SQM33.6 and 18° for 
SQM33.7) between 2 curve points in modulating mode. 

 

Bit 4 

Valency 

 16 

Sectional deviation in comparison with last referencing

 

Actuator was overloaded or mechanically twisted.  
1. Check the setting of the actuator type (parameter 613.1)

 

2. Check to see if the actuator is blocked somewhere along its working range.

 

3. Check to see if the torque is sufficient for the application. 

90 

# 

Internal error basic unit 

 

91 

# 

Internal error basic unit 

 

93 

# 

Error flame signal acquisition 

 

 3 

Short-circuit 

of 

sensor 

Short-circuit at QRB... 
1. Check wiring. 
2. Flame detector possibly fault. 

95 # 

Error 

relay 

supervision 

 

 

3 Ignition transformer 

4 Fuel valve 1 

5 Fuel valve 2 

6 Fuel valve 3 

External power supply NO contact 

Check wiring 

96 # 

Error 

relay 

supervision 

 

 

3 Ignition transformer 

4 Fuel valve 1 

5 Fuel valve 2 

6 Fuel valve 3 

Relay contacts have welded 

Test the contacts: 
1. Unit connected to power: Fan output must be dead. 
2. Disconnect power: Disconnect fan. No resistive connection between fan output and neutral  
    conductor allowed. 
If one of the 2 tests fails, release the unit since contact have definitively welded and safety can no 
longer be ensured. 

97 # 

Error 

relay 

supervision 

 

 0 

Safety relay contacts have welded or external power supply 

fed to safety relay 

Test the contacts: 
1. Unit connected to power: Fan output must be dead. 

Summary of Contents for AGM60.4A9

























































































































































































































































Reviews:

No comments