Siemens AGM60.4A9 Basic Documentation Download Page 174

Page: 174 / 248

174/248

Building Technologies Division

Basic documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

26 Info level

25.09.2013

26.2.5 Total number of startups

min s

The display shows parameter

166:

flashing on the

left, characters

._._

on the right, since the display

of the total number of startups may comprise
more than 5 digits.

Example: Parameter

166: ._._

/reset

1…3 s

h min s

ild

Press

/reset

for 1…3 s to show the total number of

startups.

Example:

/reset

ESC

min s

6/0

Press

/reset

ESC

to return to the display of

parameters.

To the next parameter

Back to the previous
parameter

26.2.6 End of info level

h min s

ild

When this display appears, you have reached the
end of the info level.

The display shows

– End –

flashing.

To the start of the info level

/reset

<1s

Back to the previous
parameter

ESC

/reset

>3 s

h min s

ild

Press

/reset

for >3 s or

ESC

to return to the

normal display.

OPErAtE

appears for a short moment.

h min s

ild

/07

When this display appears, you are back on the
normal display and you can change to the next
level mode.

Summary of Contents for AGM60.4A9

























































































































































































































































Search results

Summary of Contents for AGM60.4A9

Reviews:

Siemens AGM60.4A9, Basic Documentation, Page: 174 / 248

Search results

Summary of Contents for AGM60.4A9

Reviews: