manualshive.com logo in svg

Siemens AGM60.4A9, Basic Documentation, Page: 241 / 248

Share
Download
Siemens AGM60.4A9 Basic Documentation Download Page 241

 

241/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

30 Error code list 

25.09.2013 

Error 
code 

Diagnostic code 

Meaning for the LMV36... system 

Remedy 

113 

# 

Internal error mains voltage supervision 

Make a reset; if error occurs repeatedly, replace the unit 

115 

# 

Internal error system counter 

 

116 

0 

Designed life time exceeded (250´000 startups) 

Warning threshold has been reached. The unit should be replaced 

117 

0 

Life time exceeded 

Operation no longer allowed 

Switch-off threshold has been reached 

120 

0 

Interrupt limitation fuel meter input 

Too many disturbance pulses at the fuel meters input 

 Improve EMC 

121 #

 

Internal error EEPROM access

 

Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs 
repeatedly, replace the unit 

122 

# 

Internal error EEPROM access 

Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs 
repeatedly, replace the unit 

123 

# 

Internal error EEPROM access 

Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs 
repeatedly, replace the unit 

124 

# 

Internal error EEPROM access 

Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs 
repeatedly, replace the unit 

125 

# 

Internal error EEPROM read access 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

126 

# 

Internal error EEPROM write access 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

127 

# 

Internal error EEPROM access 

Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs 
repeatedly, replace the unit 

128 

0

 

Internal error EEPROM access - synchronization during 

initialization

Make a reset; if error occurs repeatedly, replace the unit 

129 #

 

Internal error EEPROM access – command 
synchronization

 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

130 

# 

Internal error EEPROM access - timeout 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

131 

# 

Internal error EEPROM access - page on abort 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

132 

# 

Internal error EEPROM register initialization 

Make a reset; if error occurs repeatedly, replace the unit 

133 

# 

Internal error EEPROM access – Request synchronization 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

134 

# 

Internal error EEPROM access – Request synchronization 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

135 

# 

Internal error EEPROM access – Request synchronization 

Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 

136 

1

 

Restore started 

Restore of a backup has been started (no error)  
New devices require resetting following restore! 

 

 

for further diagnostic codes for error code 136, refer to 
error code 137 

For measures, refer to error code 137 

137 

# 

Internal error – backup / restore 

 

 

157 (-99) 

Restore – ok, but backup < data set of current system 

Restore successful, but backup data record is smaller than in the current system 

 

239 (-17) 

Backup – storage of backup in AZL2... faulty 

Reset and repeat backup 

 

240 (-16) 

Restore – no backup in AZL2... 

No backup stored in AZL2... 

Summary of Contents for AGM60.4A9

























































































































































































































































Reviews:

No comments