manualshive.com logo in svg

Siemens AGM60.4A9, Basic Documentation, Page: 149 / 248

Share
Download
Siemens AGM60.4A9 Basic Documentation Download Page 149

 

149/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

18 Connection to superposed systems 

25.09.2013 

 

 

Note 
Fuel changeover on the basic unit.

 

 

After a change of fuel, the BAC system must rewrite the predefined target output. A 
change of fuel can be detected by cyclic sampling of the type of fuel currently burnt.

 

 
General setting values for connection of the basic unit to building automation (for factory 
settings, refer to the 

Parameter list

): 

 
Bus communication may only be interrupted for the time set. 
If communication is disturbed for a longer period of time, the LMV36... basic unit delivers 
a fault status message and the values set in the basic unit by building automation are 
reset. 
 

No. Parameter 

141 

Operating mode BACS 
0 = off 
1 = Modbus 
2 = reserved 

142 

Setback time in the event of communication breakdown 
 
Setting value: 
0 = inactive 
1…7200 s 

148 

Default output if communication with building automation is interrupted  
Setting values: 
 
For 

modulating operation

 the setting range is as follows: 

0…19.9 = burner OFF 
20…100 = 20…100% burner rating 
 
For 

multistage operation

, the following

 

settings apply: 

0 = burner OFF, P1, P2, P3 
Invalid = no default output from building automation 
 
Default setting: 

Invalid

 

149 

Fuel 1: Default output if communication with building automation is 
interrupted  
Setting values: 
 
For 

modulating operation

 the setting range is as follows: 

0…19.9 = burner OFF 
20…100 = 20…100% burner rating 
 
For 

multistage operation

, the following

 

settings apply: 

0 = burner OFF, P1, P2, P3 
Invalid = no default output from building automation 
 
Default setting: 

Invalid

 

 
The factory settings of the parameters are shown on the 

Parameter list

. 

 

 

Note 
For a detailed description of parameters 148 and 149, refer to chapter 

Default output 

via building automation

. 

Summary of Contents for AGM60.4A9

























































































































































































































































Reviews:

No comments