Samsung SRN-4000 User Manual Download Page 90

Page: 90 / 166

Snmp

Using the SNMP protocol, the system or network administrator can monitor the network devices remotely as

well as the operating environment.

•

Enable SNMP v1 : SNMP version 1 is used.

•

Enable SNMP v2 : SNMP version 2 is used.

- Read Community : Enter the name of read-only community to access the SNMP information. By default it is

set to <

private

- Write Community : Enter the name of write-only community to access the SNMP information. By default, it

is set to <

public

•

Enable SNMP v3 : SNMP version 3 is used.

- Password : Set the initial user password for SNMP version 3.

•

Enable SNMP Traps : SNMP trap is used to send important events and conditions to the Admin System.

- Trap Manager : Enter the IP address to which messages will be sent.

SNMP v3 can be set only if the security connection method is set to HTTPS mode.

Refer to "

SSL

" for more details. (Page 86)

90_

menu setup

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands