Samsung SRN-4000 User Manual Download Page 66 | Manualshive

Page: 66 / 166

background image

rAid mode setting

If you enable the RAID (Redundant Array of Independent Disks) mode, when a system HDD is damaged you

can restore data safely. The NVR supports RAID level 5 and 6. RAID Level 5 supported by the NVR can work to

restore data for a single HDD only in case of failure of that HDD. RAID level 6 can restore data and operation of

up to two malfunctioning HDDs.

M

`

In this NVR, you can organize two RAID. The first RAID uses only the HDDs installed in HDD slot 1 to 6, and the second RAID

uses only the HDDs installed in HDD slot 7 to 12.

`

If the RAID has 5~6 HDDs installed, you can operate and organize it.

`

You can use RAID level 6 only if a single RAID has 6 HDDs mounted in it.

•

Status : Displays the operational status of the RAID.

- Active : Signals the fact that the RAID is operating normally.
- Build : User is in process of organizing a RAID and normal operation is ongoing.
- Degraded : It is displayed when the one or more HDDs that make up the RAID are malfunctioning. When

the maximum number of HDDs allowed in the RAID level are malfunctioning, if an additional HDD

malfunctions, you cannot use or restore the RAID.

Immediately, replace the HDD and proceed with restoration.

`

For more on how to replace the HDD and to restore the RAID, refer to "

Recovering RAID Array

". (Page 68)

- Rebuilding : It means that a RAID is being restored. When the maximum allowable number of HDDs in the

RAID are being rebuilt (due to malfunctioning), if an additional HDD malfunctions, you cannot use or restore

the RAID.

- Fail : This means that the RAID cannot be used or restored.

•

Status : Displays the current operating condition of the HDDs installed in a RAID.

- Active : Displays that the HDD is operating normally.
- Faulty : It displays that the HDD is malfunctioning. You need to immediately replace the HDD for smooth

recovery of the RAID.

- Removed : It displays that a HDD does not work and cannot be detected. You need to immediately replace

the HDD for smooth recovery of the RAID.

- Restore : Displays that a HDD is being recovered.

•

Capacity : It shows the total capacity of the HDDs that composes a RAID.

•

Temperature : You can check the temperature of HDD(s) that compose a RAID.

66_

menu setup

menu setup

«
...
64
65
66
67
68
...
»

Summary of Contents for SRN-4000







































































































































































Reviews:

No comments

Related manuals for SRN-4000

Brand: NST Pages: 82

Brand: l-com Pages: 73

Brand: CPcam Pages: 65

Brand: TS-market Pages: 8

Brand: Delta Pages: 5

Brand: Magnavox Pages: 2

Brand: SMART Pages: 49

Brand: Timespace Pages: 185

Brand: Okina USA Pages: 9

Brand: ZKTeco Pages: 17

Brand: Apollo Pages: 74

Brand: IC Realtime Pages: 8

Brand: Panasonic Pages: 51

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 82

DMRHS2 - DVD RECORD.W/HD DRIV

Brand: Panasonic Pages: 94

Brand: Panasonic Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands