Samsung SRN-4000 User Manual Download Page 61

Page: 61 / 166

Live Setting

You can change the live transfer settings of the network camera.

•

Live Replacement : You can select the live profile setup mode.

If you select <

manual

>, the profile setup items are enabled, and you can change settings manually.

- Auto : For live monitoring, the profile which is approximate to the output resolution of each channel must be

selected automatically.

e.g., Camera profile : Three profiles (1280x720, 800x600 and 640x480) are supported.

If the resolution of the output screen is 1920x1080:

1280x720 is selected automatically if the channel resolution of the single channel is 1920x1080.

640x480 is selected automatically if the channel resolution of 16-split channel is 480x270.

- Manual : Live monitoring is performed with the profile selected by the user from the registered camera

profiles.

- Record : Live monitoring is performed with the profile set for recording.

•

Profile : You can select the video profile of the connected camera setting.

•

Codec : Show the codec of the selected recording profile.

•

Resolution : Show the resolution of the selected profile.

•

Frame Rate : Show the frame rate of the selected profile.

•

Quality : Show the quality of transfer video of the selected profile.

English

_61

●

enu Se

Tup

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands