Samsung SRN-4000 User Manual Download Page 16

Page: 16 / 166

16_

connecting with other device

ConneCTing The uSB

On the front of the product, there is a USB port.

You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.

If a USB HDD is connected to the system, recognition and settings are available in "

menu Setup

device

Storage device

". (Page 63)

The product supports hot plugging function that enables connecting/disconnecting USB devices while in

operating the system.

If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the NVR.

Some USB devices may fail to function properly due to compatibility issue, please check the device before using.

Only USB storage devices that comply with the standards (having a metal cover) are guaranteed for data transfer.

In case if the USB device’s electric contacts have been worn out, data transfer between the devices may not properly

function.

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands