Samsung SRN-4000 User Manual Download Page 110

Page: 110 / 166

ConTroLLing A ConneCTed neTworK CAmerA

Controlling pTZ

If PTZ camera is connected, the <

> icon appears on screen. When selecting corresponding camera

channel, the PTZ tab is provided to allow you to control the PTZ.

Item

Description

Camera menu

Displays the camera settings menu.

Direction Adjustment

Use this to adjust the direction of the camera or click the crosshair in the center to use it as an

OK button.

IRIS

Adjusts image's brightness by controling the camera's iris.

Sound

You can set the camera audio torque and mute.

PTZ speed

Adjusts the PAN, TILT reaction speed.

Preset

Sets the preset position for camera framing and moves to designated preset position when

selecting a desired preset.

Swing

Moves between the preset start point and end point.

110_

live viewer

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands