Samsung SRN-4000 User Manual Download Page 74

Page: 74 / 166

Setting the network camera's recording profile

You can configure the video profile settings for instructing the network camera (connected to each channel) to

make recording.

You can configure the settings only for the profiles that are supported by the camera.

If the profiles used for recording and network are different, camera's video feed may not comply with the frame rate as

specified in the camera.

•

Profile : Select a record profile for the connected camera.

•

Codec : Show the codec information for the selected record profile.

•

Resolution : Display the resolution for the selected record profile.

•

Frame Rate : Display the baud rate for the selected record profile.

•

Quality : Display the video quality for the selected record profile.

•

AMD : Display whether to set the Advanced Motion Detection (AMD) event for the channel.

74_

menu setup

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands