Samsung SRN-4000 User Manual Download Page 24

Page: 24 / 166

24_

live

Name

Description

System

Operation

FULL

RAID

SCSI

It is displayed when there is a malfunctioning HDD in the RAID.

There are one or two HDD malfunctions but you can still read or write to it.

FULL

RAID

SCSI

It is displayed when recovering a RAID Error.

FULL

RAID

SCSI

It is displayed when you cannot write RAID due to a malfunction of HDD.

FULL

RAID

SCSI

It is displayed when the max permitted amount of data for each channel is exceeded.

FULL

RAID

SCSI

It is displayed when due to a deterioration in network performance (10fps or less), the

AMD function fails.

FULL

RAID

SCSI

It is displayed when an iSCSI device is disconnected.

FULL

RAID

SCSI

It is displayed when the network is overloaded.

It occurs when the max receiving allowance is exceeded, causing an overload to the

CPU. It will disappear if you modify the camera settings or delete a camera to reduce

the performance burden.

FULL

RAID

SCSI

It is displayed when there is firmware to update the server.

Video Input

Status

Displayed if no input is entered in the condition that the camera is set to <

Displayed if no permission to live view is granted.

If a camera is <

OFF

>, or if no camera is registered, or it is in <

Covert2

> mode, nothing

will be displayed on the screen.

If the camera is set to <

Covert1

>, the video will be displayed but the OSD menus will not

be displayed.

Camera Title / Channel

Display the camera title and channel number.

Camera

Operation

FULL

RAID

SCSI

This icon is displayed for a channel that a PTZ-featuring camera is connected to.

FULL

RAID

SCSI

Displays AUDIO ON/MUTE. Not displayed in video mode if deactivated.

FULL

RAID

SCSI

If the sensor is set to <

>, the input signal will be displayed on the screen of the

connected channel.

FULL

RAID

SCSI

This icon is displayed when Motion Detection is set to <

> and a camera motion or

camera event occurs.

It displays the status of general/event/scheduled recording.

FULL

RAID

SCSI

It is displayed when it fails to decode all the frames due to limited decoding performance

and in this case only the I-Frame is decoded.

It is displayed when a AMD event occurs.

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands