Samsung SRN-4000 User Manual Download Page 114

Page: 114 / 166

To adjust timeline

If searched data are overlapping, you can select a desired data, move its playback time point, and zoom in/out

the timeline.

Select the number of data to search if data is overlapping.

It appears only when data are overlapped and assigns <

> to the most recent data.

Click your desired time point to play on the timeline.

The playback start point is moved.

Click <

> / <

> to zoom in/out the zoom factor to display time.

When magnified, if you want to view the pre/post timeline, click on the timeline and drag it in the direction

you want to move it.

if you want to check the recording list

The results for each recording section will be displayed.

114_

search viewer

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands