Samsung SRN-4000 User Manual Download Page 103

Page: 103 / 166

Live SCreen ConfigurATion

System Status

You can check the status or operation of the NVR with the icons on the live screen.

Item

Description

System Operation

It is displayed when there is a problem with the fan.

It is displayed when there is a problem with the power supply.

It is displayed when there is an issue with the recording conditions.

Displayed if the HDD is full and the NVR has an insufficient space to

record.

Displayed if no HDD is installed or the existing HDD should be replaced.

Displayed if the HDD needs a technical examination.

It is displayed when there is a malfunctioning HDD in the RAID.

There are one or two HDD malfunctions but you can still read or write to it.

It is displayed when recovering an RAID Error.

It is displayed when you cannot write RAID due to a malfunction of HDD.

It is displayed when the max permitted amount of data for each channel is exceeded.

It is displayed when due to a network performance degradation (10fps or less), the

AMD function fails.

English

_103

●

Live viewer

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands