Samsung SRN-4000 User Manual Download Page 48

Page: 48 / 166

Settings

You can copy and import the NVR settings by using a storage media.

•

Storage Device : Shows the connected storage device.

•

Export : Exports NVR settings to the connected storage device.

•

Import : Imports NVR settings from the storage device and applies to the NVR.

- Uncheck the checkbox of an item(s) that you want to import.

Only the other items than the selected one will be applied to the NVR.

•

Load Factory Default : Restore the factory default settings of NVR.

Uncheck the checkbox of an item(s) that you want to reset. Then, only the other items than the selected one

will return to the factory default.

If <

initialization

> is selected, a confirmation dialog for "

Load factory default

" prompts. Press <

> to

initialize the system to the factory default.

When you initialize the system without changing the <

Authority Setting

>, you must enter the ID and password to log into

the system after it reboots. The ID and password are "

admin

" and "

4321

", respectively.

Please change the password after you log in.

48_

menu setup

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands