Samsung SRN-4000 User Manual Download Page 29

Page: 29 / 166

English

_29

●

Live

view the Launcher menu

The Launcher menu appears on the bottom of the live screen.

Select <

Show Launcher

> in the context menu of the Live

screen.

Move the cursor to the bottom and click a desired item in

the Launcher menu.

If no input is entered for 10 seconds, the menu will disappear.

The Launcher menu can be accessed only by using the mouse.

Description

Layout

Select the layout to be displayed on the screen.

Layout Setup

You can set, change or delete the new layout of each channel.

Screen Mode

Displays a list of split modes available in a bar type.

The current screen mode will be displayed grey.

Menu Expansion

Button

Click to display the hidden menu to the right.

Backup

Searches for a backup device and runs backup of each channel or schedule it for later at a more

desirable time.

Zoom

Enlarges the selected area. This is available only in Single Live mode.

PTZ

If the network camera connected to the selected channel supports the PTZ operations, this will run

the PTZ control launcher. This is active only in Live single mode.

Alarm

Stops the alarm if it's activated.

d e

f g

i j

k l

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands