Samsung SRN-4000 User Manual Download Page 13

Page: 13 / 166

English

_13

●

ALLA

Tion

rACK inSTALLATion

Install the Bracket-Rack as shown in the figure, and then fasten the

screws on both sides (3 screws on each side).

Fix the screws not to be loosened by vibrations.

hdd AddiTion

Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product damage.

Please consult your provider for further information on HDD installation since improper installation or settings may

damage the product.

Number of HDDs supported : Up to 12 HDDs supported

Make sure to unplug the power cord from the wall outlet before proceeding with the installation.

Cautions for data loss (HDD care)

Please pay attention so that the data inside the HDD is not damaged.

Before adding a HDD, please check the compatibility with this product.

HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.

Please ensure that the HDD is free from such shock.

We are not liable for any damage to the HDD incurred by user's carelessness or miss use.

Cases might cause damage to HDD or recorded data

To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.

If exposed to shock when disassembling or installing, data stored in the hard disk may be damaged.

A sudden power failure or turning off the product while in HDD operation may damage the hard disk drive.

HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.

Cautions when installing a hdd

Do not apply excessive force to the HDD.

Pay attention so as not to lose the disassembly screws or accessories.

If the screws or accessories are not put together correctly, the product may breakdown or not operate properly.

Please check the HDD compatibility before adding a HDD.

Please contact your nearest dealer to obtain the list of compatible devices.

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands