Samsung SRN-4000 User Manual Download Page 8

Page: 8 / 166

overview

feATureS

The product records video and audio from network cameras to a hard disk, and enables playback from the hard disk.

It also provides remote monitoring environment for video and audio over the network using a remote computer.

•

User-friendly UI

•

VGA, 4CIF, record in a max of 2592X1944 (5M pixel) supported

•

Record and play video

•

Record and play audio

•

Supports ONVIF Pofile S standard and RTP / RTSP protocols

•

Play high-definition video using the HDMI cable

•

Display the HDD operation status by HDD SMART

•

HDD overwrite enabled

•

Backup using USB 2.0 protocols and external HDD

•

Simultaneous play of 16 channels

•

Various Search Modes (Search by Time, Event, Backup and Heatmap)

•

Various Recording Modes (Normal, Event, Scheduled Recording)

•

Alarm Input / Output

•

Remote Monitoring function by Windows Network Viewer

•

Live monitoring of the network camera

•

Advanced Motion Detection (AMD)/Heat Map (Car/Person Detection) Function

•

Installation Wizard Function (Easy Setup, Quick Setup)

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands