Samsung SRN-4000 User Manual Download Page 62

Page: 62 / 166

Channel Setting

You can configure the video settings for each channel.

•

Apply to CH : If you select <

Apply to Ch

>, the "

Apply to Ch

" confirmation window will appear.

After selecting channels that the settings will be applied to, click on <

> to apply them to the selected

channels.

•

Video

- <

on/off

> : You can turn ON/OFF the selected channel's camera.

- <

Covert1

> : Shows information other than the video of the selected channel.

For privacy protection, it does not display the video while the recording continues.

- <

Covert2

> : Shows nothing but an empty screen while the recording continues.

If the channel is set to <

Covert1

> or <

Covert2

> mode, the channel's sound is not hearable.

However, the channel's sound is recorded if its Audio setting is set to <

>, even the sound is not heard in Live mode.

•

Audio

- If set to <

>, you can turn the audio of the channel ON/OFF on the Live screen.

- If set to <

off

>, the channel's audio is off on the Live screen and not recorded.

•

Camera Name : Provide a camera Name.

You can enter up to 15 characters including space.

62_

menu setup

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands