Samsung SRN-4000 User Manual Download Page 83

Page: 83 / 166

port Setting

•

Protocol Type : Select the protocol type among TCP, UDP - Unicast and UDP - Multicast.

•

Device Port : Enter the connectable port number. Initially, <

554

> is set.

- TCP : It has better stability and lower speed when compared to UDP, and recommended for internet

environments.

•

UDP Port : Initially, <

8000~8159

> is set. It increases / decreases by 160.

- UDP : It has less stability and faster speed when compared to TCP, and recommended for local area

network (LAN) environments.

•

Multicast IP Address : User can directly input.

•

Multicast TTL : Select from 0 ~ 255. Initial value for the TTL is set to <

•

Web Streaming Port : Enter the port number for the Web Viewer. Initially, it is set to <

•

Send SSL : Select this option to send SSL.

•

Backup Bandwidth : Select the degree of backup bandwidth.

English

_83

●

enu Se

Tup

Summary of Contents for SRN-4000







































































































































































Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands

Samsung SRN-4000, User Manual

Search results

Summary of Contents for SRN-4000

Reviews:

Related manuals for SRN-4000

Brands by name

Popular brands