Samsung CLX-9251 Series Service Manual Download

Page: 126 / 481

3. Disassembly and Reassembly

3.2.1.2. Cleaning the LSU window

Open the front cover. Remove the waste toner
container[A].

Take out the LSU window cleaning tool that is located
on the front cover.

Insert the LSU window cleaning tool to each color hole.

Slowly pull out and push the cleaning tool.

Repeat step 4 at least 5 times for each LSU window.

3-4

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands