Samsung CLX-9251 Series Service Manual Download Page 237 | Manualshive

Page: 237 / 481

background image

4. Troubleshooting

4.4.7. SFE (Special Feature Enablement)

Special Feature Enablement (SFE) means to provide the configurable options (On/Off) in service mode for technicians or
dealers to satisfy the requirements from B2B sites easily without changing the firmware installed in a device.

SFE menu description

•

Service Mode > SFE > Letterhead/Preprinted paper handle (001)

If this option is enabled, in case of printing in directional media (Letterhead/Preprinted), the device prints as the
same output direction regardless of simplex or duplex.

•

Service Mode > SFE > Mono Print only mode (002)

If this option is enabled, the device always prints output as mono about PC printing.

•

Service Mode > SFE > Copy Speed (004)

If this option is enabled, the device accelerates the scan speed of ADF copy by reducing scan resolution from 600 dpi
to 300 dpi.

•

Service Mode > SFE > Print Output (005)

If this option is enabled, the device provides the same output direction about Flatbed printing and ADF printing.

NOTE

Refer to the following table for SFE supported in each model.

SFE Code

Title

CLX-9201/

9251/ 9301

(Polaris

Color)

SCX-8123/

8128

(Polaris

Mono)

CLX-9252/

9352

(Cosmos-R

Color)

SCX-8230/

8240

(Cosmos-R

Mono)

CLX-8640/

8650

(Evergreen)

001

Letterhead/Preprinted paper handle

O

O

O

O

O

002

Mono Print only mode

O

X

O

X

O

004

Copy Speed

O

O

O

O

X

005

Print Output

O

O

X

X

X

Copyright© 1995-2016 SAMSUNG. All rights reserved.

4-52

«
...
235
236
237
238
239
...
»

Summary of Contents for CLX-9251 Series


































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CLX-9251 Series

Brand: Triumph Adler Pages: 424

Brand: Xerox Pages: 108

Brand: Canon Pages: 200

COLORPASS-Z6000 PS-NX6000

Brand: Canon Pages: 144

ColorPASS-Z5000

Brand: Canon Pages: 214

IR5000 - iR B/W Laser

Brand: Canon Pages: 839

Brand: Canon Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands