Samsung CLX-9251 Series Service Manual Download Page 359

Page: 359 / 481

4. Troubleshooting

► Error Code

S2–1211

S2–2311

S2–3110

► Error message

Engine System Failure: #S2-1211. Turn off then on

Engine System Failure: #S2-2311. Turn off then on

Engine System Failure: #S2-3110. Turn off then on

► Symptom

The main board is defective.

► Troubleshooting method

1) Turn the machine off then on.

2) If the problem persists, turn the machine off again.

3) Replace the main board(

JC92–02429A

4) Turn the machine on.

► Error Code

S2–3114

► Error message

Engine System Failure #S2-3114: Turn off then on.

► Symptom

ACR error has occurred.

► Troubleshooting method

1) Execute “ACR calibration” manually.

(

Machine Setup > General Settings > Image Management > Auto Color Registration

)

2) Clean the ACR sensor.

(

Refer to 3.2.1.1. Cleaning the ACR/CTD sensor window

)

3) If the problem persistss, replace the main board(

JC92-02429A

4-174

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands