Samsung CLX-9251 Series Service Manual Download Page 284

Page: 284 / 481

4. Troubleshooting

► Error Code

C1–5311

► Error message

Black Toner Cartridge Failure: #C1-5311. Install black toner cartridge again

► Symptom

Black toner supply is inefficient or abnormal.

► Troubleshooting method

1) Open the front cover.

2) Remove the black toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside

the cartridge.

3) Check if the toner supply pipe is blocked. If it is closed, open it.

4) Close the front cover.

4-99

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands