Samsung CLX-9251 Series Service Manual Download Page 375

Page: 375 / 481

4. Troubleshooting

► Error Code

U1–2316

U1–2317

► Error message

Fuser Unit Failure: #U1-2316.

Fuser Unit Failure: #U1-2317.

► Symptom

Temperature of the fuser changes abnormally.

► Troubleshooting method

1) Turn the machine off. Re-install the fuser unit, then turn the machine on.

(Refer to 3.2.2. Fuser unit)

2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?)

3) If the problem persists, Check the following :

(Refer to 3.3.23. Fuser unit)

a) Check if the Halogen lamp

(110V : 4713-001630 / 220V : 4713–001631)

is broken or disconnected.

b) Check if the AC connection of the Halogen lamp is disconnected or contaminated.

c) Check if the thermistat

(4712-001098)

is disconnected.

d) Check if non-contact type thermistor

(1404–001453)

is broken.

4) If the problem persists, replace the Fuser unit

(110V : JC91-01064A, 220V : JC91-01063A).

4-190

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands