Samsung CLX-9251 Series Service Manual Download

Page: 280 / 481

4. Troubleshooting

► Error Code

C1–4110

► Error message

Prepare new cyan toner cartridge.

► Symptom

Cyan toner is almost empty.

► Troubleshooting method

1) Order new cyan toner cartridge because toner cartridge with level of “Low” will be exhausted soon.

► Error Code

C1–4120

C1–4130

C1–4140

► Error message

Replace with new cyan toner cartridge

End of life, Replace with new cyan toner cartridge

► Symptom

The cyan toner cartridge is at the end of its life.

► Troubleshooting method

1) Open the front cover.

2) Remove the cyan toner cartridge.

3) Install the new cyan toner cartridge (

CLT-C809S

)

4) Close the front cover.

4-95

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands