Samsung CLX-9251 Series Service Manual Download Page 347

Page: 347 / 481

4. Troubleshooting

► Error Code

M3–1413

M3–1414

► Error message

Paper jam in exit area.

► Symptom

Paper jam has occurred around the fuser unit.(Job separator connection is defective. / Actuator-Exit is defective.)

► Troubleshooting method

1) Open the side cover. Remove the jammed paper.

2) If the problem persists, check the following:

a) Open the side cover. Check if the connector is connected properly.

b) Remove the JOB-SEPARATOR. Check if the photo sensor is assembled correctly.

c) Check if ACTUATOR-EXIT is assembled correctly. If the ACTUATOR-EXIT (

JC66-02533A

) is deformed or

broken, replace it.

d) If the photo sensor(

0604-001393

) is defective, replace it.

4-162

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands