Samsung CLX-9251 Series Service Manual Download Page 406

Page: 406 / 481

4. Troubleshooting

4.7. Adjusting the LSU skew error

1) Check the skew error

a) Execute the ACR.

(

Machine Setup > General Settings > Image Management > Auto Color Registration

)

b) Print the ACR report.

(SVC(Tech) mode > Information > Print Reports > Auto Color Registration)

c) Check [Y] [M] [C] Skew Data in ACR report.

2) Adjusting the skew error

a) Open the front cover. Remove the waste toner container.

b) There are 3 skew holes for YMC color. Insert the (+) screw driver and adjust CW, CCW referred to adjustment

amount

i) The standard value for skew is 200. If the skew data in ACR report, the skew adjustment is unnecessary.

ii) Adjustment method

•

Skew Data <200 : Rotate the driver in a counterclockwise direction.

ex) Skew Data is 192. : 200-192=8 Click CCW rotation

•

Skew Data = 200 : No need to adjustment.

•

Skew Data > 200 : Rotate the driver in a clockwise direction.

ex) Skew Data is 213. : 213–200=13 Click CW rotation

NOTE

1 Click is equal to 1/7 dot.

4-221

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands