Samsung CLX-9251 Series Service Manual Download Page 369

Page: 369 / 481

4. Troubleshooting

4.5.7. U1-xxxx type (Fuser) error code

► Error Code

U1–2113

U1–2119

► Error message

Fuser Unit Failure: #U1-2113.

Fuser Unit Failure: #U1-2119.

► Symptom

The thermistor can’t measure temperature. The hear-roller will not heat-up.

► Troubleshooting method

1) Turn the machine off. Re-install the fuser unit, then turn the machine on.

(Refer to 3.2.2 Fuser unit)

2) Remove the fuser unit. After openinging the jam cover, check if jammed or wrapped paper is in the fuser unit.

3) If the problem persists, check the following :

(Refer to 3.3.23. Fuser unit)

a) Check if the Halogen lamp

(110V : 4713-001630 / 220V : 4713–001631)

is broken or disconnected.

b) Check if the AC connection of the Halogen lamp is disconnected or contaminated.

4-184

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands