Samsung CLX-9251 Series Service Manual Download Page 355

Page: 355 / 481

4. Troubleshooting

► Error Code

S1–2510

S1–2511

S1–2520

S1–2521

S1–2523

S1–2540

► Error message

MSOK System Failure #S1-2510: Turn off then on.

MSOK System Failure #S1-2511: Turn off then on.

MSOK Failure: #S1-2520. Call for service.

MSOK Failure: #S1-2521. Call for service

PPM data is incorrect. Call for service & change MSOK

MSOK Failure: #S1-2540. Call for service & change MSOK

► Symptom

MSOK is not installed properly. / MSOK is defective.

► Troubleshooting method

1) Remove the rear cover.

(

Refer to 3.3.2 Rear Cover

)

2) Check if the MSOK is inserted correctly. Remove and reinstall it.

3) If the problem persists, replace the main board(

JC92–02429A

(

Refer to 3.3.7 Main Board

)

4-170

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands