Sabo 52-S A Operator'S Manual Download Page 39

Page: 39 / 88

Assembling the baffle plate (figure T1 )

Pos: 13.19 / Innenteil/ Sicherhe itshinweise/Sicherheitshinweis: Ste in @ 0\mo d_1115200949078_6. docx @ 333 @ @ 1

Safety information!

For explanation of symbols, see the table on page 3

Pos: 13.20 / Innenteil/ Vorbe reitende Arbe iten/Pra llb lech anba uen Hinweis @ 15\mod_1301471100051_6.docx @ 126161 @ @ 1

IMPORTANT
Operating the device without a baffle plate may lead to injuries caused by
objects being thrown into the air. Only operate the device with a baffle plate.

Pos: 13.21 / Innenteil/ Vorbe reitende Arbe iten/Pra llb lech anba uen Text 52er P rofi S @ 13\mod_1280313820002_6. docx @ 110327 @ @ 1

–

Fold out the mounting bracket of the baffle plate.

–

Screw the baffle plate into place in the mower housing using the pre-assembled

screws in the bracket.

CAUTION

When not paying due care and attention, fingers may be crushed when
opening the live baffle plate.

Pos: 13.22 / Innenteil/ Vorbe reitende Arbe iten/1.1 Schnitthöhe e instellen ( Abbildung I) @ 0\mod _1115201229609_6.d ocx @ 335 @ 2 @ 1

Adjusting the cutting height (figure I )

Pos: 13.23 / Innenteil/ Sicherhe itshinweise/Sicherheitshinweis: Messe r, Moto rStop @ 0\mod _1115201376187_6.d ocx @ 339 @ @ 1

Safety information!

For explanation of symbols, see the table on page 3

Pos: 13.24 / Innenteil/ Vorbe reitende Arbe iten/ Schnitthöhe einstellen Text 52er, 54er P rofi @ 21\mod_1350978940358_6.docx @ 159626 @ @ 1

–

At each wheel, pull the lever (1) towards the wheel and click it back into the

desired position by pushing it to the side.

–

All four levers should be in the same position!

CAUTION

When adjusting the cutting height, hold the adjusting lever by the handle, see
figure I . This prevents hands from slipping during adjustment and injuries

from occurring.

Pos: 14.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_6.do cx @ 41 @ @ 1

Pos: 14.2 /Innente il/Vo r de r Ersten Inbetrieb nahme/1 VOR DER ERST EN INBETRIEBN AHME M ÄH ER @ 0\mod_1115210527828_6.docx @ 361 @ 1 @ 1

BEFORE INITIAL USE

Pos: 14.3 /Innente il/Siche rheitshinweise/ Sicherhe itshinweis: Stein @ 0\mod _1115200949078_6.do cx @ 333 @ @ 1

Safety information!

For explanation of symbols, see the table on page 3

Pos: 14.4 /Innente il/Vo r de r Ersten Inbetrieb nahme/ Allgeme ine Siche rheitshinweise Benzinmähe r + Text DLG @ 37\mod _1436248174398_6.do cx @ 400214 @ @ 1

Check all screw connections and the spark plug connector for a tight fit. Tighten the

screws, if necessary. You must particularly check the fastening of the cutter bar

(see chapter “Maintenance of the cutter bar”).

The blade fastening screw must always be tightened by an authorised workshop. If

the blade screw is tightened excessively or insufficiently, blade coupling and cutter
bar may be damaged or get loose, which can lead to serious injuries.
The lawn mower is fitted with an engine stop fixture. Before using the equipment for
the first time, make sure that the engine stop safety control bar is working perfectly.

When the control bar is released, engine and cutter bar must come to a standstill
within three seconds. After release, the bar must always return to the position shown

in the “Description of components” diagram.

If this is not the case, it must be checked immediately by an authorised workshop.

Risk of injury!

If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.

Measuring the stopping time

After starting the combustion engine, the blade rotates and a wind noise can be
heard. The stopping time corresponds to the duration of the wind noise after the

combustion engine has been switched off; it can be measured with a stopwatch.

Pos: 14.5 /Innente il/Vo r de r Ersten Inbetrieb nahme/ Siche rheits- und Schutzeinrichtungen ... dürfen nicht manip ulie rt ode r deaktivie rt we rden!_dl_text @ 38\mod_1437988093850_6.docx @ 402468 @ @ 1

Machine safety and protective devices must not be manipulated or disabled.

Pos: 14.6 /Innente il/Vo r de r Ersten Inbetrieb nahme/Da rauf achten ... Schutze inrichtunge n ord nung sgemäß ange bra cht und nicht be schäd igt sind! @ 37\mod _1436249863921_6.do cx @ 400690 @ @ 1

Make sure that all protective devices have been attached properly and are not

damaged.

Pos: 14.7 /Innente il/Vo r de r Ersten Inbetrieb nahme/1.1 Öl einfülle n (Abb ild ung Y1 ) @ 0\mo d_1115210961078_6. docx @ 365 @ 2 @ 1

Filling with oil (figure Y1 )

Pos: 14.8 /Innente il/Siche rheitshinweise/ Sicherhe itshinweis: Ex plosion @ 0\mo d_1115210618640_6. docx @ 363 @ @ 1

Safety information!

For explanation of symbols, see the table on page 3

Pos: 14.9 /Innente il/Vo r de r Ersten Inbetrieb nahme/Öl einfüllen H inweis Mo tor J S63 @ 3\mod_1158825745978_6.docx @ 20352 @ @ 1

IMPORTANT

Avoid damage! Engine is delivered without oil. You must add oil before

running the engine.

Pos: 14.10 / Innenteil/ Vor de r Erste n Inbe triebnahme/ Öl einf üllen Text Moto r B& S 550 E-Se rie s, 675EXi, 650 Qua ntum @ 44\mod _1469090694063_6.do cx @ 504524 @ @ 1

Before the first start, fill in engine oil (quantity and quality see technical data) with
a funnel into this opening after unscrewing the dipstick.
-

Park the mower on level ground.

Fill in the oil slowly through the filler. Do not overfill. After filling in the oil, wait

for about one minute and then check the oil level.
Insert the dipstick and tighten it.

–

Checking the oil level

Remove the dipstick. Wipe the dipstick with a clean cloth, reinsert and tighten it.

Pull out the dipstick again and read off the oil level. The oil must be at the top of
the full marking (arrow). If necessary, refill oil. However, the oil level must not
be above the full marking. Reinsert the dipstick and tighten it.

After the first filling, remove the “OIL HAS BEEN DRAINED

FOR SHIPPING”

sign at the top of the engine.

Pos: 14.11 / Innenteil/ Vor de r Erste n Inbe triebnahme/1. 1 Kraftstoff einfüllen @ 0\mod_1115211956203_6.docx @ 371 @ 2 @ 1

Filling with fuel

Pos: 14.12 / Innenteil/ Sicherhe itshinweise/Sicherheitshinweis: Explo sion, Benzin @ 0\mod_1115211811093_6. docx @ 369 @ @ 1

Safety information!

For explanation of symbols, see the table on page 3

Pos: 14.13 / Innenteil/ Vor de r Erste n Inbe triebnahme/Kraf tstoff einfülle n Text @ 0\mo d_1127830250803_6. docx @ 1258 @ @ 1

–

Only fill the tank with fresh and clean unleaded standard petrol. Fuel with up to

10% ethanol is acceptable.

–

Unscrew the tank cap.

–

Fill tank with fuel using a funnel up to max. lower edge of the filling nozzle.

–

Replace tank cap and screw tight.

Pos: 15.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_6.do cx @ 41 @ @ 1

STARTING THE ENGINE (FIGURE D + E )

Pos: 15.3 /Innente il/Siche rheitshinweise/ Sicherhe itshinweis: Fuss, Stein, Ab stand @ 0\mod_1115212854781_6.docx @ 379 @ @ 1

Safety information!

For explanation of symbols, see the table

on page 3

Pos: 15.4 /Innente il/Starten des Motors/ Allgemeine Sicherheitshinweise Se itenauswurf @ 27\mod_1381834277264_6.do cx @ 200529 @ @ 1

Only start the engine when standing behind the mower. Do not stand on the ejection

side. Always place the mower on a level area which is not covered with high grass
(if the grass is too high it will block the start-up of the cutter bar and make the

starting process more difficult). When the engine is started, the machine must not
be tilted on end, if necessary it must be tilted by pressing the guide bar down so that

the cutting tool is pointing in the direction away from the user, but only as far as
absolutely necessary. As long as the device has not been lowered to the ground

again, both of your hands must be on the top part of the bar.

Pos: 15.5 /Innente il/Starten des Motors/ Sta rte rseilgriff während de s Startens fest umfasse n VORSICHT @ 13\mod_1280234045462_6.docx @ 110216 @ @ 1

CAUTION

Hold the starter cable handle firmly when starting. The handle may otherwise
slip out of your hand. Risk of injury!

Pos: 15.6 /Innente il/Starten des Motors/H inweis: W ICHT IG @ 0\mod_1115213366156_6.docx @ 385 @ @ 1

IMPORTANT

The engine will only run when the safety control bar on the upper handlebar

section is pressed. The moment the control bar is released, the latter will
return into its original position by spring force, the engine brake is activated

and engine and cutter bar will come to a standstill within three seconds.

Pos: 15.7 /Innente il/Starten des Motors/H inweis: Ready Sta rt-Sy stem, opt. max.Drehzahl (W14 fixed speed) @ 12\mod_1262874621558_6.docx @ 104067 @ @ 1

NOTE

This engine has a temperature-controlled automatic choke.
The engine runs automatically at an optimum maximum speed, which is required for
a clean cut pattern (engine speed = blade speed).

Pos: 15.8 /Innente il/Starten des Motors/ Sta rten de s Moto rs Text SAU10718, SAU12675, SA S, SAU 12178 @ 14\mod_1282216093170_6. docx @ 113878 @ @ 1

–

Press the safety control bar (1) onto the upper handlebar section (2) and hold it

there

–

Slowly pull the starter cable (3) until resistance is felt, then pull it out

rapidly

–

the engine starts to run

–

, slowly recoil the cable.

SWITCHING OFF THE ENGINE (FIGURE F )

Pos: 16.3 /Innente il/Abstellen des Mo tors/Ab stelle n des Motors Tex t Be nzin @ 1\mod_1133871931563_6.do cx @ 7086 @ @ 1