Ryobi RY36CSX35A, Original Instructions Manual

Page: 10 / 328

8 | English
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only. When servicing, use only original
replacement parts.
WARNING
Remove the battery before adjustment, maintenance or
cleaning. Failure to do so could result in serious personal
injury.
■
You may make adjustments or repairs described in
this manual. For other repairs, contact the authorized
service agent.
■
Consequences of improper maintenance, removal, or
modification of safety features, such as the chain brake,
ignition switch, hand guard (front and back), spiked
bumper, chain catcher, guide bar, and low kickback
saw chain may cause the safety features to not function
correctly, thus increasing the potential for serious
injury. Keep your chainsaw professionally maintained
and safe.
■
Sharpening the chain safely is a skilled task. Therefore
the manufacturer strongly recommends that a worn
or dull chain is replaced with a new one, available
from your authorised RYOBI service centre. The part
number is available in the product specification table
in this manual.
■
Follow instructions for lubricating and chain tension
checking and adjustment.
■
After each use, clean the product with a soft, dry cloth.
■
Check all nuts, bolts, and screws at frequent intervals
for security to ensure the product is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by an authorized service centre.
MAINTENANCE SCHEDULE
Daily check
Bar lubrication Before each use
Chain tension Before each use and
frequently
Chain sharpness Before each use, visual
check
For damaged parts Before each use
For loose fasteners Before each use
Chain brake function Before each use
Inspect and clean
Bar Before each use
Complete saw After each use
Chain brake Every 5 hours*
* Hours of operation
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■
injury caused by vibration
– Always use the right tool for the job, use designated
handles and restrict working time and exposure.
■
damage to hearing due to exposure to noise
– Wear hearing protection and limit exposure.
■
injury caused by contact with exposed saw teeth of the
chain (cutting hazards)
■
injury caused by unforeseen, abrupt movement or
kickback of the guide bar (cutting hazards)
■
injury caused by parts ejected from the saw chain
(cutting/injection hazards)
■
injury caused by thrown-out pieces of the workpiece
(wood chips, splinters)
■
injury caused by dust and particles
■
injury to the skin caused by contact with lubricants
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
Keep your body warm in cold weather. When operating
the product. Wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
■
After each period of operation, exercise to increase
blood circulation.