ROOTECH ACCURA 2300S Manual Download Page 24

Page: 24 / 176

Chapter 1 Introduction

Accura 2300S/2350-1P3FSC User Guide

Page 24

ⓒ

Product Features

Accura 2300S Distribution Panel Digital Power Meter

Accura 2300S collects data from multiple Accura 2350 modules connected with the 6C telephone line

and displays data on its LCD screen.

Accura 2300S

Function

Voltage Measurement in the Incoming Feeder

Measures voltage by sensing voltage in the incoming feeder in distribution panels

Display

Displays the measurement data on Accura 2300S, as well as the data collected from
Accura 2350 modules on its LCD screen

Measurement Parameters

Voltage

Line-to-neutral voltage, Line-to-line voltage, and Frequency

Fundamental

voltage

5, 3

, Vector diagram (phasor)

THD

, Harmonics

5, 3

Unbalance according to symmetrical components (negative-/zero-
sequence components)

, unbalance as per the NEMA standard

Residual voltage

5, 6

Temperature

Measures the temperature of Accura 2300S with a sensor located
at the rear of the device

Power Quality

Dip(Sag), Swell

RMS voltage measured over 1 cycle and refreshed each half cycle

Harmonics

Up to the 40th order

Unbalance

Line-to-neutral voltage/Line-to-line voltage unbalance, voltage
unbalance according to negative-/zero-sequence components

Measurement Events

Event type

Dip(Sag), Swell events

Phase open events

Fuse fail events

Over-temperature events

Over-current events

Over leakage current events

Over demand current events

Over power events

Number of event
logs

Maximum 100

Internal Communication with Accura 2350

Dedicated

Sends the sampled voltage data to multiple Accura 2350 modules

communication

Collects measurement data from multiple Accura 2350 modules

Number of connected modules

Up to 15 per port

Length of the 6C telephone line

Up to 6 m per port

External Communication

with the Host System

Ethernet

100 Mbps/Full Duplex, Modbus TCP protocol

Ethernet switching with 2 ports

Wiring mode: star, daisy-chain, ring topology (RSTP

supported)

RS-485

1,200

–

115,200 bps

, Modbus RTU protocol

Summary of Contents for ACCURA 2300S














































































































































































Search results

Summary of Contents for ACCURA 2300S

Reviews:

Related manuals for ACCURA 2300S

Brands by name

Popular brands

ROOTECH ACCURA 2300S, Manual

Search results

Summary of Contents for ACCURA 2300S

Reviews:

Related manuals for ACCURA 2300S

Brands by name

Popular brands