ROOTECH ACCURA 2300S Manual Download Page 143

Page: 143 / 176

Accura 2300S/2350-1P3FSC User Guide

Chapter 5 Measurements

ⓒ

Page 143

Chapter 5 Measurements

General Measurement

The general measurement parameters of Accura 2300S are shown in the following table. Some of the

parameters are provided only via communications.

The LCD screen on the front of the device provides measurement values obtained at 2-second

aggregation intervals based on the measurement values obtained at a frame of 0.5 seconds.

Measurement data are also provided via communication. Measured values provided via communication

are values obtained for the aggregation intervals of 0.5, 1, and 5 seconds, 1 and 5 minutes, 1 and 6

hours. The default aggregation interval is set to 1 second.

The maximum and minimum values Accura 2300S provides after resetting the values are stored in the

nonvolatile memory. Thus, the data are maintained even when Accura 2300S is turned off. The peak

demand value is reset to zero by resetting the maximum/minimum values not demand values.

▣

Shown on Accura 2300S and provided via communication

▲

Available only via communication

Measurement Parameter

Phase Average

/ Total

Aggregation Interval After Resetting Unit
Avg.

Max. Min.

Voltage

Line-to-neutral

▣

▲

▣

Line-to-line

▣

▲

▣

Fundamental

▲

THD

1, 2

▣

▲

Phasor

▲

Line-to-neutral unbalance (NEMA MG1)

▲

Line-to-line unbalance (NEMA MG1)

▲

Zero-sequence unbalance

▲

Negative-sequence unbalance

▲

Residual voltage

▲

Frequency

▣

▲

Temperature of Accura 2300S

▣

▲

Current

▣

▲

▣

Fundamental

▣

▲

THD

/ TDD

▣

▲

Phasor

▲

Crest Factor

▲

K-Factor

▲

Leakage current

▣

▲

Power

Active power

▣

▲

▣

Reactive power

▣

▲

▣

kVAR

Apparent power

▣

▲

▣

kVA

Power Factor

▣

▲

Phase angle Lead/Lag

▣

▲

Energy

Received active energy

▣

kWh

Delivered active energy

▣

kWh

Sum active energy

▣

kWh

Summary of Contents for ACCURA 2300S














































































































































































Search results

Summary of Contents for ACCURA 2300S

Reviews:

Brands by name

Popular brands

ROOTECH ACCURA 2300S, Manual

Search results

Summary of Contents for ACCURA 2300S

Reviews:

Brands by name

Popular brands