PRÜFTECHNIK VIB 5.300 EX Series Operating Instructions Manual Download Page 70

Page: 70 / 172

3-16

VIBXPERT 11.2010

Measurement - Machine template

The template then appears, which – like a route – is displayed as a
tree structure or in the form of a list* (see section ‘Route’). The
following steps are identical to those in the ‘Route’ section:

• Click on the measurement location.

• Select the measurement task, and connect the sensor specified in

the info field.

• Click on the measurement task to start the measurement.

• Select the next measurement task and start the measurement.

Once all measurement tasks have been completed, the following
message appears: 'All measurements on the machine carried out!'

* not in the case of templates for
production tests

Summary of Contents for VIB 5.300 EX Series













































































































































































Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands

PRÜFTECHNIK VIB 5.300 EX Series, Operating Instructions Manual

Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands