PRÜFTECHNIK VIB 5.300 EX Series Operating Instructions Manual Download Page 164

Page: 164 / 172

6-18

VIBXPERT 11.2010

Appendix - Troubleshooting

Troubleshooting

Symptom:

VIBXPERT will not start up. The start procedure is not executed
completely, the display stops at the screen showing the LINUX
penguin.

Cause:

Failure in the flash memory.

Solution:

Reload the firmware.

Reloading firmware

Before reloading the firmware, ensure that the following components
are at hand or installed on the PC:

VIBXPERT update tool version 1.47 or higher (see P. 2-37).

Serial cable - VIB 5.430-2

Ethernet cable - VIB 5.331

Communication adapter for VIBXPERT EX (VIB 5.330-UNV)

• Connect VIBXPERT to the serial port and to the network connector

of the PC. Use the two cables mentioned above or, for VIBXPERT
EX, the communication adapter (see p. 2-33).

• Start the VIBXPERT update tool on the PC.

• Click on the 'Start Emergency Recovery' button. A warning is

issued that the following process deletes all data on the memory
card. Confirm to continue, or save the card content before
confirming.

• In the next screen, set up the COM port to be used on the PC and

enter the IP address that is to be used by VIBXPERT. If the IP
address of the PC is not identified automatically, enter it in the
appropriate field.

Summary of Contents for VIB 5.300 EX Series













































































































































































Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands

PRÜFTECHNIK VIB 5.300 EX Series, Operating Instructions Manual

Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands