PRÜFTECHNIK VIB 5.300 EX Series Operating Instructions Manual Download Page 154

Page: 154 / 172

6-8

VIBXPERT 11.2010

Appendix - VIBXPERT utility

• Click on the 'Background image' button.

• Select a background image for the VIBXPERT start window

(format: PNG, size: 320x480 px, color: gray scale, 4-bit color
depth) and load it into the device.

Deleting background images: Use 'Delete files' in the 'Service''
menu (see p. 2-31).

• How to display the image in the start window is described in the

'Device Setup - Display' section (see p. 2-13).

Transferring files

The following files can be transferred from the device to the PC:
-

PDF files generated with a PDF printer driver.

Screenshots generated by pressing <F> & <-> simultaneously .

Results in CSV format for analysis and display in a spreadsheet
program (eg MS Excel).

• Click on the 'Get files' button.
• Then click on the respective button and select the files you wish to

transfer.

• Click on 'Transfer' to start the file transfer.

Use 'Delete' to remove a file from the device. 'Close' closes the file
selection window.

Get files

File selection window

Summary of Contents for VIB 5.300 EX Series













































































































































































Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands

PRÜFTECHNIK VIB 5.300 EX Series, Operating Instructions Manual

Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands