PRÜFTECHNIK VIB 5.300 EX Series Operating Instructions Manual Download Page 153

Page: 153 / 172

6-7

VIBXPERT 11.2010

Appendix - VIBXPERT utility

Connection

Setting up a connection with VIBXPERT

Data transmission takes place via a network or USB connection.

• Connect VIBXPERT to the network or a PC using the cable

provided (see also p. 2-32).

• Click on the 'Connection' button.

• Set the type of connection (USB or Ethernet).

•

For Ethernet only:

Enter the IP address of the data collector in the

network in the 'IP address' field (see also p. 2-34f.).

• To test the connection, click on the 'Test communication' button. If

the connection is working, a yellow 'Smiley' symbol appears. A red
'Smiley' symbol indicates a faulty connection.

VIBXPERT successfuly connected

Configuring VIBXPERT

The configuration encompasses the following functions:
- Updating the firmware
- Transferring logo images for the report printouts

• Click on the 'Configure device' button.

• The 'New firmware' button starts the 'VIBXPERT update tool' that

updates the firmware in VIBXPERT (see also p. 2-37f.).

This program must be installed in the designated directory on the
PC:
C:\Programs\Pruftechnik\vibxpert\VxpUpdateTool

• Click on 'Report-Logo' button, to load a new logo image into

VIBXPERT. The logo appears on each printed report page top
right. File requirements:

Format: PNG / Size: 200 pixel (longest side)

Device configuration



Note

Summary of Contents for VIB 5.300 EX Series













































































































































































Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands

PRÜFTECHNIK VIB 5.300 EX Series, Operating Instructions Manual

Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands