PRÜFTECHNIK VIB 5.300 EX Series Operating Instructions Manual Download Page 5

Page: 5 / 172

1-5

VIBXPERT 11.2010

Contents

Chapter 1: Introduction ..................................................... 1-8

VIBXPERT delivery packages ....................................................... 1-9

Safety and operating notes ...................................................... 1-12

Chapter 2: Getting started ................................................ 2-1

VIBXPERT FFT data collector and signal analyzer ......................... 2-1

Keyboard .................................................................................................... 2-2
Status display per LED ................................................................................. 2-3

Notes on operation .................................................................... 2-4

Interfaces ................................................................................... 2-5

Interfaces on VIBXPERT with intrinsic safety ................................................ 2-6

Power supply ............................................................................. 2-7

Charging in the device ................................................................................ 2-7
Charging in the external charging station .................................................... 2-8

Power supply - intrinsically safe device ....................................... 2-9

Carrying pouch - VIB 5.354 ........................................................ 2-9

Belt ............................................................................................................. 2-9
Hand strap .................................................................................................. 2-9

Memory card ........................................................................... 2-10

Replacing the memory card ....................................................................... 2-10

Basic settings - Device Setup .................................................... 2-12

Date & Time .............................................................................................. 2-12
Display settings, switchoff and additional options ..................................... 2-13
Route ........................................................................................................ 2-14
Transducers ............................................................................................... 2-19

Available transducers in VIBXPERT ....................................................... 2-19
Tranducer detection and Hardware settling ......................................... 2-22
Sensor test .......................................................................................... 2-22
Default vibration sensor (Multimode) ................................................... 2-22
Keyphaser ........................................................................................... 2-23

Setting up a printer ............................................................................. 2-26
Deleting a print job ............................................................................. 2-27
Connecting the printer ........................................................................ 2-27

Analog out/headphones ............................................................................ 2-28
Service menu ............................................................................................ 2-29

Device Info .......................................................................................... 2-29
Offset Compensation .......................................................................... 2-29
Factory Defaults .................................................................................. 2-29
LogLevel .............................................................................................. 2-30

Memory card (CF) ..................................................................................... 2-31
Standardization factor for dB scaling ......................................................... 2-31
Deleting files ............................................................................................. 2-31

Data transfer ........................................................................... 2-32

Summary of Contents for VIB 5.300 EX Series













































































































































































Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands

PRÜFTECHNIK VIB 5.300 EX Series, Operating Instructions Manual

Search results

Summary of Contents for VIB 5.300 EX Series

Reviews:

Related manuals for VIB 5.300 EX Series

Brands by name

Popular brands