PRÜFTECHNIK VIB 5.300 EX Series Operating Instructions Manual Download Page 142 | Manualshive

Page: 142 / 172

background image

5-26

VIBXPERT 11.2010

F

Measurement tasks

Tips for setting the measurement parameters

Set the 'Trigger Start" time to a negative value in order to record
the signal before the excitation.

If the measurement starts before the excitation, increase the trigger
threshold in the measurement setup by approximately half (P. 3-22).

If the response signal overloads, increase the 'Measurement Range'
parameter in the measurement setup accordingly (P. 3-22).



Note

Measurement with the machine running

• Enable 'Negative averaging' in the measurement setup.
• Perform the individual impact tests.
• Click on 'Start' in the window that opens to measure the reference

spectrum - without producing a machine excitation!

• Click on 'Stop' when a sufficient number of reference spectra have

been recorded and averaged to form a result.

Displaying the results

• Activate the upper display field with the F key (Spectrum, P. 4-8).
• Press the MENU key and click on 'Choose Dataset'.

The results of the impact test, the average final result and the
reference measurement (negative averaging) are listed here and
can be displayed individually by clicking (see below).

• To close the list, press on the ESC key.

Repeating individual measurements

• Activate the upper display field using the F key.
• Press the MENU key and click on 'Repeat'.
• Click on the respective measurement in the list.

ESC

Left:

Reference measurement

is required when measuring on a

running machine

Right:

Dataset selection

Single measurements /

Averaged final result

«
...
140
141
142
143
144
...
»

Summary of Contents for VIB 5.300 EX Series













































































































































































Reviews:

No comments

Related manuals for VIB 5.300 EX Series

Brand: Labom Pages: 5

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: Vanguard Instruments Company Pages: 62

Brand: Vanguard Instruments Company Pages: 58

Brand: KROHNE Pages: 56

Brand: Omega Pages: 13

Brand: Gates Pages: 112

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

Brand: Velleman Pages: 15

Brand: Konica Minolta Pages: 42

Brand: Kobold Pages: 12

Brand: pts Diagnostics Pages: 2

LeakTracker OIL-GLO ULTRA

Brand: Spectroline Pages: 12

Brand: Vectronics Pages: 2

Brand: Resol Pages: 24

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands