Panasonic KX-TVP50E Installation Manual Download Page 48

Page: 48 / 368

INTEGRATING THE VPS WITH PANASONIC KX-T PHONE SYSTEMS

Installation Manual

Digit Translation Table Parameters

These parameters allow PBXs that have a fixed Follow-on ID sequence to be used with the
KX-TVP50. For example, a Follow-on ID sequence of [

201] can be changed to [#6201]

by using these parameters.

•

Inter-Digit Time-Out:

This parameter defines the duration of incoming signals

(Follow-on ID) from the PBX to the VPS. The Digit Translation Table is applied to the
digits received within this time.

•

Input-Output (up to 8 alphanumeric characters):

When the system receives digits

within the inter-digit time, it checks them against the input table. If they are found, the
system utilises the output digits in their place.

Forwarded to Extn. The extension dialled is forwarded to another, non-Voice

Mail extension.

Confirmation Tone The Message Waiting Lamp On or Message Waiting Lamp

Off code is dialled successfully.

Disconnect

The caller disconnects. The local exchange must send a
CPC signal to the PBX for this feature to work on outside
calls.

Table 11

Code

(default)

Call State

Sent to the Voice Mail Port When...

The Remainder of this section consists of step-by-step guides for software verification
and programming of the recommended Panasonic PBX systems.

Summary of Contents for KX-TVP50E

















































































































































































































































































































































































Search results

Summary of Contents for KX-TVP50E

Reviews:

Related manuals for KX-TVP50E

Brands by name

Popular brands

Panasonic KX-TVP50E, Installation Manual

Search results

Summary of Contents for KX-TVP50E

Reviews:

Related manuals for KX-TVP50E

Brands by name

Popular brands