Panasonic KX-TVP50E Installation Manual Download Page 326

Page: 326 / 368

MESSAGE MANAGER'S GUIDE

326

Installation Manual

526

TEN

[526]

527

TEN [HOUR]

[527]

528

TEN [MINUTE]

[528]

529

TENTH

[529]

530

Thank you

[530]

531

Thank you for calling

[531]

532

The callback number is (telephone
number)

[532], [647], [392]

533

The callback number is not assigned [533], [647], [392]

534

The FAX transfer situation is as
follows

[534]

535

The first 4 letters of the owner's last
name are (name)

[535]

536

Mailbox number entry failure
Check the mailbox number

[536]

537

The message is (message)

[537]

538

The message sender is unknown

[518], [538]

539

The prompt is now turned off mode

[539]

540

The system-reserved mailbox cannot
be edited

[540]

541

There are (number)

[541], [ 43]

542

There are no messages

[542]

543

There was 1 unsuccessful attempt to
enter this mailbox

[543]

544

There were (number of failure)

[544], [809]

545

These are the brief segments of your
Message

[545]

546

THIRD

[546]

547

Third telephone number is (telephone
number)

[547]

548

Third telephone number is not
assigned

[548]

549

THIRTEEN

[549]

Table 81

Prompt

No.

Modifiable Prompts

Linked to Prompt No. (s)

Summary of Contents for KX-TVP50E

















































































































































































































































































































































































Search results

Summary of Contents for KX-TVP50E

Reviews:

Brands by name

Popular brands

Panasonic KX-TVP50E, Installation Manual

Search results

Summary of Contents for KX-TVP50E

Reviews:

Brands by name

Popular brands